Iscar Releases A Completely New Family Of Slitting Cutters Using Tang-Grip Technology And The Strength Of Sumo Tec Grades
Iscar at this time offers a family of high-performance slitting tools that couple the convenience and security of Tang-Grip clamping with the increased durability of the brand new Sumo Tec insert grades.
The conception, already verified effective in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets with a distinct hand tool, and are retained tightly in place without the need for clamps, upper jaws or set screws that can weaken the insert and obstruct chip flow. The pocket composition utilizes cutting forces to keep the insert seated firmly in position, preventing any danger of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus longer pocket and insert life.
Iscar's Sumo Tec insert grades showcase a unique post-coating treatment which extensively improves tool life and reliability.
Unveiled in late 2007, the revolutionary Sumo Tec treatment smooths the insert's coated surface to eradicate microscopic stress raisers, diminish heat and friction and increase chip flow. The result is enhanced toughness and resistance to chipping and built-up edge, all leading to longer tool lifespan. The golden-colored side on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters offer more teeth than Iscar's SGSF cutters, allowing higher feed rates.
Their increased rigidity leads to straighter, additional accurate cuts and lowered vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same assortment of inserts as Tang-Grip parting tools. Some other sizes will be added.
Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate beneath a Sumo Tec TiAlN PVD coating, delivering exceptional resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.
IC830, offering additional toughness for heavier parting & grooving including interrupted cuts. It is suited for all stainless steel and high temperature alloys.
IC908, a hard, fine-grain substrate with superior chipping resistance, mixed with a brand new Sumo Tec TiAlN PVD coating. It is ideal for nodular or gray cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades suited for stainless steel, high temperature alloys and other alloy steels. These grades are likewise suggested for interrupted cuts and heavy operations.
All Tangslit and Tang-Grip inserts are presented in J- or C-type chipformer geometries from Iscar.
Iscar Adds Their Most Recent Creations To A Long Line Of Successful Hole Producing Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
Some Of The Many Improvements In Carbide Inserts From Iscar From Over The Last Decade
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.
Original Tools And Carbide Insert Configurations From Iscar To Better Maximize The Machining Method
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
The Most Recent In Carbide Endmill Configuration In A Long And Productive Family From Iscar
Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
New End Mills Coming From Iscar Will Raise Productivity While Decreasing Costs
Manufacturers and die & mold shops can banish chatter problems in numerous milling operations with Iscar's new Chatterfree end mills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the primary source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
Commercial Water Heater - Considering All Of Your Needs - Read Carefully To Know A Lot More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.
Completely New Car Manufacturing Jobs To Help Save The Economic State
The global recession the economy is experiencing in the past few years have pushed major companies to close down and stop their operations.
|
